기본으로 지원되는 단축키는 없다. 명령을 만들어서 단축키로 연결 해야한다.

# 활성화된 창의 모니터 위치를 변경하는 프로그램 작성 및 단축키 등록

# 필수 패키지 설치

1
apt install xdotool wmctrl

# 쉘 스크립트 생성

예제, /opt/move-to-next-monitor/move-to-next-monitor.sh:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
#!/bin/sh
#
# Move the current window to the next monitor.
#
# Also works only on one X screen (which is the most common case).
#
# Props to
# http://icyrock.com/blog/2012/05/xubuntu-moving-windows-between-monitors/
#
# Unfortunately, both "xdotool getwindowgeometry --shell $window_id" and
# checking "-geometry" of "xwininfo -id $window_id" are not sufficient, as
# the first command does not respect panel/decoration offsets and the second
# will sometimes give a "-0-0" geometry. This is why we resort to "xwininfo".


screen_width=$(xdpyinfo | awk '/dimensions:/ { print $2; exit }' | cut -d"x" -f1)
screen_height=$(xdpyinfo | awk '/dimensions:/ { print $2; exit }' | cut -d"x" -f2)
display_width=$(xdotool getdisplaygeometry | cut -d" " -f1)
display_height=$(xdotool getdisplaygeometry | cut -d" " -f2)
window_id=$(xdotool getactivewindow)


# Remember if it was maximized.
window_horz_maxed=$(xprop -id "$window_id" _NET_WM_STATE | grep '_NET_WM_STATE_MAXIMIZED_HORZ')
window_vert_maxed=$(xprop -id "$window_id" _NET_WM_STATE | grep '_NET_WM_STATE_MAXIMIZED_VERT')


# Un-maximize current window so that we can move it
wmctrl -ir "$window_id" -b remove,maximized_vert,maximized_horz


# Read window position
x=$(xwininfo -id "$window_id" | awk '/Absolute upper-left X:/ { print $4 }')
y=$(xwininfo -id "$window_id" | awk '/Absolute upper-left Y:/ { print $4 }')


# Subtract any offsets caused by panels or window decorations
x_offset=$(xwininfo -id "$window_id" | awk '/Relative upper-left X:/ { print $4 }')
y_offset=$(xwininfo -id "$window_id" | awk '/Relative upper-left Y:/ { print $4 }')
x=$(( x - x_offset))
y=$(( y - y_offset))


# Compute new X position
new_x=$((x + display_width))
# Compute new Y position
new_y=$((y + display_height))


# If we would move off the right-most monitor, we set it to the left one.
# We also respect the window's width here: moving a window off more than half its width won't happen.
width=$(xdotool getwindowgeometry "$window_id" | awk '/Geometry:/ { print $2 }'|cut -d"x" -f1)
if [ "$(( new_x + width / 2))" -gt "$screen_width" ]; then
new_x=$((new_x - screen_width))
fi


height=$(xdotool getwindowgeometry "$window_id" | awk '/Geometry:/ { print $2 }'|cut -d"x" -f2)
if [ "$((new_y + height / 2))" -gt "$screen_height" ]; then
new_y=$((new_y - screen_height))
fi


# Don't move off the left side.
if [ "$new_x" -lt 0 ]; then
new_x=0
fi


# Don't move off the bottom
if [ "$new_y" -lt 0 ]; then
new_y=0
fi


# Move the window
xdotool windowmove "$window_id" "$new_x" "$new_y"


# Maximize window again, if it was before
if [ -n "${window_horz_maxed}" ] && [ -n "${window_vert_maxed}" ]; then
wmctrl -ir "$window_id" -b add,maximized_vert,maximized_horz
elif [ -n "${window_horz_maxed}" ]; then
wmctrl -ir "$window_id" -b add,maximized_horz
elif [ -n "${window_vert_maxed}" ]; then
wmctrl -ir "$window_id" -b add,maximized_vert

# /usr/local/bin 등록

1
sudo ln -s /opt/move-to-next-monitor/move-to-next-monitor.sh /usr/local/bin/move-to-next-monitor

# 설정 -> 키보드에서 단축키와 명령을 연결

1
ctrl + alt + tab ::: /usr/local/bin/move-to-next-monitor